Drive Shaft Sho..
Fuel Injector C..
Go Fast Bits
South Bend Clut..
60K and Tune-up
Apparel and Decals
Blow Off Valves
Dash - Displays
Decals and Emblems
Intercoolers - Piping
Oil System Parts
Shifters - Parts
Used OEM Parts
Aem Water Methanol Injection Kit 1 Gallon 30-3000
Click to enlarge
Aem Water Methanol Injection Kit 1 Gallon 30-3300
Water/methanol injection for forced induction (turbocharged or supercharged) gas-powered race engines is a proven means for effectively reducing engine inlet air temperatures and suppressing harmful detonation. This allows racers to reliably increase boost and advance ignition timing?without using high-octane racing fuel?for power gains of up to 20%. AEM?s Water/Methanol Injection Systems utilize the most robust hardware combined with more advanced features than any other comparably priced water/methanol system.
Water Methanol Injection for forced induction vehicles up to 35 PSI of boost. The Boost Dependent controller has an on-board manifold absolute pressure (MAP) sensor with a molded-in nipple for a boost hose pickup.
Robust, Easy to Use Controller Designs
The new controller designs (Boost Dependent Kit PN 30-3300 & Multi Input Kit PN 30-3350) feature large, turn-resistant knobs and larger numbering to easily set accurate start and full activation points, with covered status LED and test buttons for added splash resistance. A plug is integrated into the controller housing for mating to the redesigned wiring harness?s positive-lock connector. The Boost Dependent controller housing has a molded-in, barbed nipple to accept a boost hose and a wiring legend on the back. Both controller housings feature an easy to access integrated fuse and molded mounting tabs.
AEM?s Water/Methanol Injection kit?s wiring harness is terminated with a positive-lock connector on one end and has color-coded wires to ease installation. Both the power and ground wires for the pump are included in the harness which simplifies the wiring process and eliminates any chance of the pump accidentally activating from a short in the system. An additional wire is included for adding an optional on/off solenoid to stop fluid flow when the system is inactive.
Integrated Boost Safe Feature
The controllers in AEM?s Water Methanol systems include an integrated ?Boost Safe? output feature that monitors the entire injection system and triggers a ground signal via an output if it detects a voltage-related error (short, bad connection, broken wire, overheated pump, high or low voltage signal, etc.), allowing users to define their failsafe strategy from something as simple as flashing a warning light to more advanced strategies like pulling boost or ignition, or switching fuel maps on a standalone engine management system. Combined with the integral and highly accurate conductive low-fluid switch in the tank, ?Boost Safe? can also put your engine in safe mode before the system runs dry. This exclusive feature is found only on AEM Water/Methanol Injection Systems.
Heavy-Duty High Pressure Injection Pump
AEM?s internally-bypassed water/methanol injection pump does not cycle on and off and provides quiet, smooth operation. It features robust construction including integral hose fittings, EPDM seals and a Santoprene diaphragm that provides consistent and reliable fluid delivery.
Low-Profile 1 Gallon Tank
AEM?s gas Water/Methanol Injection Systems are available with or without a compact 1 gallon tank. A more accurate, conductive low level fluid sensor is integrated into the tank and features a positive lock connector with color-matched wires to the wiring harness. The sensor eliminates any chance of incorrect readings due to interference from debris.
Machined Billet Injectors and Nozzles
AEM includes one precision-machined billet injector in its gasoline Water/Methanol Injection kit. It features an integral check valve to prevent unintended fluid flow. Three billet injector nozzles are included for matching water/methanol flow to an engine?s horsepower output.
AEM strongly recommends that users never exceed a 50% methanol concentration when using any AEM Water Methanol system or component.
All AEM Water/Methanol injection systems and components (pump, lines, fittings, filter, flow sensor, tank, and nozzles) are 100% chemically compatible with methanol. However, for safety reasons we strongly recommend that users never use more than a 50% methanol concentration in our systems.
Customers who bought this product also purchased
Snow Performance Boost Juice 4 Gallons
Additional Shipping $20
Click for Shopping Cart
Click for New Items
Mitsubishi OEM 3000GT Stealth DOHC AC Compressor Cast Bracket to Mount - Bolt Kit
Click for Specials
Borla XR-1® Stainless Sportsman Racing Muffler - 40943
Write a review on this product!
Tell A Friend
Tell someone you know about this product.
Notify me of updates to
Aem Water Methanol Injection Kit 1 Gallon 30-3000
News and Updates
Service Manuals - Guides
Shipping & Returns
Conditions of Use
Click Here For
Thursday 13 December, 2018
20980811 Page Visits and Counting!
Copyright © 2018