Ninja Performance
  Top » » Water/Meth Inj » 30-3302 My Account  |  Cart Contents  |  Checkout   
Search
 

Advanced Search
Manufacturers
60K and Tune-up
Accessories
Air-Intake
Apparel and Decals
Audio
Battery-Cables-Hardware
Bearings
Belts
Blow Off Valves
Body
Boost Controllers
Brackets-Braces
Brakes
Bushing Kits
Cam Gears
Camshafts
Catch Cans
Clutch Master
Clutch Slave
Clutches
Cooling
Crankshaft
Dash - Displays
Decals and Emblems
Driveline
Driveshafts-CV Shafts
Electronics
Engine
Engine Management
Engine Mounts
Exhaust
Exterior
Fasteners
Fittings-Adapters
Flywheels
Fuel
Gaskets-Seals-Plugs
Gauge Pods
Gauges
Hoses
Ignition-Plugs
Intercoolers - Piping
Interior
Lighting
Nitrous Oxide
Oil System Parts
Oil-Filters
Oil-Fluids
Package Deals
Piston Pins
Piston Rings
Pistons
Pulleys
Reservoirs
Rods
Sensors-Controllers
Service
Shifters - Parts
Silicone Couplers
Steering
Suspension
T-Bolt Clamps
Tech data
Tools
Transfer Case
Transmission
Turbo
Turbo Timers
Used OEM Parts
Used Parts
Vacuum Hose
Valvetrain
Wastegate
Water/Meth Inj
Wideband
Wrist Pins
Additional Shipping
Other Makes
Aem Water Methanol Injection Kit No Tank 30-3302
[30-3302]
$407.95

Aem Water Methanol Injection Kit No Tank 30-3302

Water/methanol injection for forced induction (turbocharged or supercharged) gas-powered race engines is a proven means for effectively reducing engine inlet air temperatures and suppressing harmful detonation. This allows racers to reliably increase boost and advance ignition timing?without using high-octane racing fuel?for power gains of up to 20%. AEM?s Water/Methanol Injection Systems utilize the most robust hardware combined with more advanced features than any other comparably priced water/methanol system.

THIS KIT DOES NOT INCLUDE A TANK

Water Methanol Injection for forced induction vehicles up to 35 PSI of boost. The Boost Dependent controller has an on-board manifold absolute pressure (MAP) sensor with a molded-in nipple for a boost hose pickup.

Robust, Easy to Use Controller Designs
The new controller designs (Boost Dependent Kit PN 30-3300 & Multi Input Kit PN 30-3350) feature large, turn-resistant knobs and larger numbering to easily set accurate start and full activation points, with covered status LED and test buttons for added splash resistance. A plug is integrated into the controller housing for mating to the redesigned wiring harness?s positive-lock connector. The Boost Dependent controller housing has a molded-in, barbed nipple to accept a boost hose and a wiring legend on the back. Both controller housings feature an easy to access integrated fuse and molded mounting tabs.

Simplified Wiring
AEM?s Water/Methanol Injection kit?s wiring harness is terminated with a positive-lock connector on one end and has color-coded wires to ease installation. Both the power and ground wires for the pump are included in the harness which simplifies the wiring process and eliminates any chance of the pump accidentally activating from a short in the system. An additional wire is included for adding an optional on/off solenoid to stop fluid flow when the system is inactive.

Integrated Boost Safe Feature
The controllers in AEM?s Water Methanol systems include an integrated ?Boost Safe? output feature that monitors the entire injection system and triggers a ground signal via an output if it detects a voltage-related error (short, bad connection, broken wire, overheated pump, high or low voltage signal, etc.), allowing users to define their failsafe strategy from something as simple as flashing a warning light to more advanced strategies like pulling boost or ignition, or switching fuel maps on a standalone engine management system. Combined with the integral and highly accurate conductive low-fluid switch in the tank, ?Boost Safe? can also put your engine in safe mode before the system runs dry. This exclusive feature is found only on AEM Water/Methanol Injection Systems.

Heavy-Duty High Pressure Injection Pump
AEM?s internally-bypassed water/methanol injection pump does not cycle on and off and provides quiet, smooth operation. It features robust construction including integral hose fittings, EPDM seals and a Santoprene diaphragm that provides consistent and reliable fluid delivery.

Machined Billet Injectors and Nozzles
AEM includes one precision-machined billet injector in its gasoline Water/Methanol Injection kit. It features an integral check valve to prevent unintended fluid flow. Three billet injector nozzles are included for matching water/methanol flow to an engine?s horsepower output.

AEM strongly recommends that users never exceed a 50% methanol concentration when using any AEM Water Methanol system or component.

All AEM Water/Methanol injection systems and components (pump, lines, fittings, filter, flow sensor, tank, and nozzles) are 100% chemically compatible with methanol. However, for safety reasons we strongly recommend that users never use more than a 50% methanol concentration in our systems.

Reviews

See Ninja Performance 

Reviews at Bizrate.com

Click Here For
Ninja Performance
Customer Testimonials

Click for Shopping Cart
0 items
Click for New Items
AEM CD-7 Digital Racing Dash Display 30-5500
AEM CD-7 Digital Racing Dash Display 30-5500
$1,299.00
Click for Specials
Driveshaft Shop Carbon Fiber Driveshaft 6 Speed
Driveshaft Shop Carbon Fiber Driveshaft 6 Speed
$1,574.99
$1,274.99
Reviews
Write ReviewWrite a review on this product!
Tell A Friend
 
Tell someone you know about this product.
Notifications
NotificationsNotify me of updates to Aem Water Methanol Injection Kit No Tank 30-3302
Information
About Us
News and Updates
Service Manuals - Guides
Shipping & Returns
Privacy Notice
Conditions of Use
Contact Us


Copyright © 2018 Ninja Performance