Ninja Performance
  Top » » Transfer Case » NP25splineOS My Account  |  Cart Contents  |  Checkout   
Search
 

Advanced Search
Manufacturers
60K and Tune-up
Accessories
Air-Intake
Apparel and Decals
Audio
Battery-Cables-Hardware
Bearings
Belts
Blow Off Valves
Body
Boost Controllers
Brackets-Braces
Brakes
Bushing Kits
Cam Gears
Camshafts
Catch Cans
Clutch Master
Clutch Slave
Clutches
Cooling
Crankshaft
Dash - Displays
Decals and Emblems
Driveline
Driveshafts-CV Shafts
Electronics
Engine
Engine Management
Engine Mounts
Exhaust
Exterior
Fasteners
Fittings-Adapters
Flywheels
Fuel
Gaskets-Seals-Plugs
Gauge Pods
Gauges
Hoses
Ignition-Plugs
Intercoolers - Piping
Interior
Lighting
Nitrous Oxide
Oil System Parts
Oil-Filters
Oil-Fluids
Package Deals
Piston Pins
Piston Rings
Pistons
Pulleys
Reservoirs
Rods
Sensors-Controllers
Service
Shifters - Parts
Silicone Couplers
Steering
Suspension
T-Bolt Clamps
Tech data
Tools
Transfer Case
Transmission
Turbo
Turbo Timers
Used OEM Parts
Used Parts
Vacuum Hose
Valvetrain
Wastegate
Water/Meth Inj
Wideband
Wrist Pins
Additional Shipping
Other Makes
Ninja Performance 25 Spline 5 and 6 Spd AWD Output Shaft
[NP25splineOS]
$279.99 $249.99

Ninja Performance 25 Spline 5 and 6 Spd AWD Output Shaft

Replace your old worn out output shaft with this Ninja Performance Output Shaft.

When the output shaft is worn, so is the input spool. They should be replaced as a pair. If you only replace one or the other, the worn down teeth of the older part damages and accelerates the wear on the newer part causing premature weak and failure.

*This Shaft is for a 5 or 6 spd AWD 25 spline transaxle and transfer case. Make sure this is the shaft you need.

*Made from 8620 Steel

*Heat Treated to a hardness of HRC 57-61

This Transaxle Output Shaft is a step above the OEM parts but it is NOT as strong or bullet proof as our 300M Shafts.

It can be damaged on higher powered applications, and on repeated hard launches on the street, or with the even more shocking launches at a sticky drag strip.

Know your intended use before purchasing.

For a stock powered to mildly upgraded VR4/RTTT in the 300 to 400 AWHP range this setup works well and we have had great results with both customer builds here at our shop and on customer's cars that build them themselves.

But be honest with yourself and the cars use and power. If you have higher than 400 or so AWHP and WILL be launching it hard either on the street and or track, we would recommend NOT trying to save a few dollars on this setup.

For higher horsepower and track use/launching we would highly recommend stepping up to the Ninja Performance 300M Shaft and Flexor input spool. Seen Here:

Ninja Performance Flexor Spool
Click Here for Ninja Performance Flexor Spool

Ninja Performance 300M Output Shaft
Click Here for 300M Output Shaft

Fits:
Mitsubishi 3000GT VR4 AWD Getrag Transaxle 5 speed 25 Spline
Dodge Stealth RT/TT AWD Getrag Transaxle 5 speed 25 Spline

We offer pressing services!
This requires a 40 ton press. Which we have in our service garage.

Choose the Pressing service below and send your old spool to us. We will press off the bearings and gear, press on your gear and bearings on to your new spool and cover the shipping back to you.

As with most aftermarket wear items, this Shaft and Input spool kit can not be warrantied due to breakage caused by abuse, hard launches etc and on cars exceeding stock or near stock power. ANY aftermarket high performance part can be damaged when not used on the correct application or if used in a manner it was no intended for.



If you are looking for a more bullet proof setup and or have a higher horsepower car and or visit the dragstrip often, we highly recommend the 300M/Flexor shaft and spool combo. While we have been selling these for many years with only 1 failure due to a hard launch with bad engine mounts to add to the trauma, they can fail if abused.

Ninja Performance will not be responsible for failure of these wear items unless it is deemed a manufacture defect.

Ninja Performance will not be held responsible for collateral damage caused by part failure.

Reviews
Customers who bought this product also purchased
Mitsubishi OEM AWD Getrag 5 spd Shift Shaft Return Spring
Mitsubishi OEM AWD Getrag 5 spd Shift Shaft Return Spring
Additional Shipping $150
Additional Shipping $150
Mitsubishi OEM EVO Oil Cap W/Seal
Mitsubishi OEM EVO Oil Cap W/Seal
Mitsubishi OEM Oil Filter MZ690116
Mitsubishi OEM Oil Filter MZ690116
Mitsubishi OEM 6G72 DOHC Timing Belt
Mitsubishi OEM 6G72 DOHC Timing Belt
Mitsubishi OEM 6G72 DOHC Heater Hose Kit
Mitsubishi OEM 6G72 DOHC Heater Hose Kit
Mitsubishi OEM 6G72 DOHC Timing Belt Tensioner Pulley Bolt
Mitsubishi OEM 6G72 DOHC Timing Belt Tensioner Pulley Bolt
Mitsubishi OEM 3000GT Stealth Coolant Overflow Reservoir 1991-1997
Mitsubishi OEM 3000GT Stealth Coolant Overflow Reservoir 1991-1997
Mitsubishi 3000GT Stealth AWD Carrier Bearing
Mitsubishi 3000GT Stealth AWD Carrier Bearing

See Ninja Performance 

Reviews at Bizrate.com

Click Here For
Ninja Performance
Customer Testimonials

Click for Shopping Cart
0 items
Click for New Items
Mitsubishi OEM 3000GT Stealth DOHC AC Compressor Cast Bracket - 3 Bolt
Mitsubishi OEM 3000GT Stealth DOHC AC Compressor Cast Bracket - 3 Bolt
$179.99
$149.99
Click for Specials
Borla XR-1 Stainless Sportsman Racing Muffler - 40943
Borla XR-1 Stainless Sportsman Racing Muffler - 40943
$168.99
$139.99
Reviews
Write ReviewWrite a review on this product!
Tell A Friend
 
Tell someone you know about this product.
Notifications
NotificationsNotify me of updates to Ninja Performance 25 Spline 5 and 6 Spd AWD Output Shaft
Information
About Us
News and Updates
Service Manuals - Guides
Shipping & Returns
Privacy Notice
Conditions of Use
Contact Us


Copyright © 2018 Ninja Performance