Ninja Performance
  Top » » Transfer Case » NP25splineIS My Account  |  Cart Contents  |  Checkout   
Search
 

Advanced Search
Manufacturers
60K and Tune-up
Accessories
Air-Intake
Apparel and Decals
Audio
Battery-Cables-Hardware
Bearings
Belts
Blow Off Valves
Body
Boost Controllers
Brackets-Braces
Brakes
Bushing Kits
Cam Gears
Camshafts
Catch Cans
Clutch Master
Clutch Slave
Clutches
Cooling
Crankshaft
Dash - Displays
Decals and Emblems
Driveline
Driveshafts-CV Shafts
Electronics
Engine
Engine Management
Engine Mounts
Exhaust
Exterior
Fasteners
Fittings-Adapters
Flywheels
Fuel
Gaskets-Seals-Plugs
Gauge Pods
Gauges
Hoses
Ignition-Plugs
Intercoolers - Piping
Interior
Lighting
Nitrous Oxide
Oil System Parts
Oil-Filters
Oil-Fluids
Package Deals
Piston Pins
Piston Rings
Pistons
Pulleys
Reservoirs
Rods
Sensors-Controllers
Service
Shifters - Parts
Silicone Couplers
Steering
Suspension
T-Bolt Clamps
Tech data
Tools
Transfer Case
Transmission
Turbo
Turbo Timers
Used OEM Parts
Used Parts
Vacuum Hose
Valvetrain
Wastegate
Water/Meth Inj
Wideband
Wrist Pins
Additional Shipping
Other Makes
Ninja Performance 25 Spline 5 Spd Input Spool
[NP25splineIS]
$279.99 $249.99

Ninja Performance 25 Spline 5 Spd Input Spool

Replace your old worn out Input Spool with this Ninja Performance Spool kit

When the output shaft is worn, so is the input spool. They should be replaced as a pair. If you only replace one or the other, the worn down teeth of the older part damages and accelerates the wear on the newer part causing premature weak and failure.

*This Input Spool is for a 5 spd 25 spline transaxle and transfer case. Make sure this is the kit you need.

*Made from 8620 Steel

*Heat Treated to a hardness of HRC 57-61

This Transfer Case Input spool is a step above the OEM part but it is NOT as strong or bullet proof as our Flexor Steel Input Spools.

They can be damaged on higher powered applications, and on repeated hard launches on the street, or even more shocking to the drivetrain, launching on a sticky track.

Know your intended use before purchasing.

For a stock powered to mildly upgraded VR4/RTTT in the 300 to 400 AWHP range this setup works well and we have had great results with both customer builds here at our shop and on customer's cars that build them themselves.

But be honest with yourself and the cars use and power. If you have higher than 400 or so AWHP and/or WILL be launching it hard either on the street and or track, we would recommend NOT trying to save a few dollars on this setup and stepping up to the Ninja Performance 300M Shaft and Flexor input spool. Seen Here:

Ninja Performance Flexor Spool
Click Here for Ninja Performance Flexor Spool

Ninja Performance 300M Output Shaft
Click Here for 300M Output Shaft

Fits:
Mitsubishi 3000GT VR4 AWD 5 speed 25 Spline Getrag Transfer Case
Dodge Stealth RT/TT AWD 5 speed 25 Spline Getrag Transfer Case

We currently only carry the NP Output Spool for the 5 spd Transfer case. It will not work in the 6 Spd Transfer case.

As with most aftermarket wear items, this Input spool can not be warrantied due to breakage caused by abuse, hard launches etc and on cars exceeding stock or near stock power. ANY aftermarket high performance part can be damaged when not used on the correct application or if used in a manner it was no intended for.



If you are looking for a more bullet proof setup and or have a higher horsepower car and or visit the dragstrip often, we highly recommend the 300M/Flexor shaft and spool combo. While we have been selling these for many years with only 1 failure due to a hard launch with bad engine mounts to add to the trauma, they can fail if abused.

Ninja Performance will not be responsible for failure of these wear items unless it is deemed a manufacture defect.

Ninja Performance will not be held responsible for collateral damage caused by part failure.

We offer pressing services!
This requires a 40 ton press. Which we have in our service garage.

Choose the Pressing service below and send your old spool to us. We will press off the bearings and gear, press on your gear and bearings on to your new spool and cover the shipping back to you.

If you choose the Pressing Service Below
Ship your old Spool with both bearings and pinion gear still attached to:

Ninja Performance LLC
324 Depot St
Mount Croghan, SC 29727

Available Options:
Spool Pressing Service:
Reviews
Customers who bought this product also purchased
Ninja Performance 5 spd Transfer Case Cage
Ninja Performance 5 spd Transfer Case Cage
RED LINE Heavy Shockproof 1 QT
RED LINE Heavy Shockproof 1 QT
Mitsubishi 3000GT Stealth Transfer Case Seals - Input and Output
Mitsubishi 3000GT Stealth Transfer Case Seals - Input and Output
Ninja Performance Fuel Pump Hotwire Kit - 30 Amp
Ninja Performance Fuel Pump Hotwire Kit - 30 Amp
Ninja Performance MBC
Ninja Performance MBC
Mitsubishi OEM 3000GT Stealth AWD Transaxle End Case Cap-Seal w/Oil Guide
Mitsubishi OEM 3000GT Stealth AWD Transaxle End Case Cap-Seal w/Oil Guide
Techna-Fit 3000GT Stealth Stainless Steel Braided Brake Lines AWD Clear
Techna-Fit 3000GT Stealth Stainless Steel Braided Brake Lines AWD Clear
Mitsubishi 3000GT Stealth Front Sway Bar End Link OEM
Mitsubishi 3000GT Stealth Front Sway Bar End Link OEM
Mitsubishi OEM 3000GT Stealth Weatherstrip Outside Upper Door Left and Right Pair
Mitsubishi OEM 3000GT Stealth Weatherstrip Outside Upper Door Left and Right Pair

See Ninja Performance 

Reviews at Bizrate.com

Click Here For
Ninja Performance
Customer Testimonials

Click for Shopping Cart
0 items
Click for New Items
Additional Shipping $225
Additional Shipping $225
$225.00
Click for Specials
Standalone EMS - 3000GT Stealth
Standalone EMS - 3000GT Stealth
$1,799.00
$1,479.99
Reviews
Write ReviewWrite a review on this product!
Tell A Friend
 
Tell someone you know about this product.
Notifications
NotificationsNotify me of updates to Ninja Performance 25 Spline 5 Spd Input Spool
Information
About Us
News and Updates
Service Manuals - Guides
Shipping & Returns
Privacy Notice
Conditions of Use
Contact Us


Copyright © 2018 Ninja Performance